SearchSite Map
MTI Instruments
Company
Technology
Products
News & Events
MTI University
Contact Us

Fiber Optic Measurement Systems

MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.

MTI-2100 Fotonic - Fiber-optic sensors for vibration and displacement measurements

MTI-2100 Fotonic

Extremely high resolution fiber-optic sensors for vibration and displacement measurements.
View Product

Fiber-optic Edge Position Sensing

Fotonic Edge Probe

Fotonic Edge Probe

Custom fiber-optic probe designed to measure dynamic position of thin objects.
View Product

Displacement Measurement Principle Using Fiber Optic Sensors -
An Introduction to the Fotonic Sensor

MTI-2100 Fotonic Sensor

FIGURE 1: MTI-2100 Fotonic Sensor™

The Fotonic Sensor™ is a non-contact instrument which uses the fiber optics lever principle to perform displacement, vibration and surface-condition measurements.(See Figure 1) The Fotonic Sensor transmits a beam of light through a flexible fiber-optic probe, receives light reflected from a target surface, and converts this light into an electrical signal proportional to the distance between the probe tip and the target being measured. A simplified example of the fiber optic principal is shown in Figure 2. The output signal voltage from the fiber optic sensor is then used to determine position, displacement, vibration amplitude, frequency and waveshape of a target surface.

FIGURE 2: Fiber Optic Probe Principles

Fiber Optic Probe Principles

The operation of the Fotonic Sensor is illustrated in Figures 3 and 4. Figure 3 shows that when a fiber optic probe is mounted close to a target, the amount of reflected light (A) seen by the receiving fibers (B2) is small. However, as the target moves further away from the probe (Figure 4), the amount of light illuminated on the receiving fibers (B2) increases rapidly. Even small target movements in this range cause a significant increase in the amount of received light.

FIGURE 3: Sensor Reflected Light is Low, Close to Target

Sensor Reflected Light is Low, Close to Target

FIGURE 4: Maximum Reflected Light from Fiber Optic Sensor

Maximum Reflected Light from Fiber Optic Sensor

If you plot a curve of the voltage output (proportional to the light intensity received) verses the distance between the target and the fiber optic sensor you will find that the relationship is very sensitive when the probe is close to the target. This highly sensitive area is called the front slope of the performance curve (Figure 5), typical values as listed as Range 1 in Table 1.

FIGURE 5: Fiber Optic Probe Response Curve

Fiber Optic Probe Response Curve

Increasing the distance further causes the illuminated area (A) in Figure 4 to enlarge, increasing the amount of reflected light seen by the receiving fibers (B2). Eventually, area B2 becomes saturated indicating that the fibers are accepting the maximum amount of light possible. At this point, the MTI-2100 Fotonic Sensor generates the maximum voltage output. This apex is called the optical peak. The displacement range over which the initial voltage rises and where the maximum output occurs is a function of the probe diameter and numerical aperture (N.A.) of the fibers, not the surface reflectivity.

Adjusting the amplitude of the optical peak provides the output sensitivity required for inspection and comparison of surface conditions. It is also used to calibrate each fiber optic probe to duplicate the sensitivity factors established at MTII. Figure 6 shows three different reflective surfaces.

FIGURE 6: Fiber Optic Probe Response Curves to Different Target Reflectance

Fiber Optic Probe Response Curves to Different Target Refelectance

Curve A: Instrument response curve if target reflectance is high.

Curve B: Calibrated instrument response curve.

Curve C: Instrument response curve if target reflectance is low.

Note that the optical peak occurs at the same operating distance for each of the three samples. By adjusting the amplitude of this peak to match the amplitude set at MTII during the calibration process (Curve B) the front slope and back slopes can be replicated. This slope, or sensitivity value, is stored in the memory of the MTI-2100 plug in module and used to convert voltage to a displacement or position. The MTI-2100 has a calibration process that allows you to duplicate this curve and “self calibrate” to your specific target reflectivity. If the target reflectance is either too high (Curve A) or too low (Curve C), compared to the calibrated curve (B), the user simply adjusts the transmitted light intensity by pushing the “cal” button.

If higher sensitivity is required the light intensity can be increased even further. For example, a 20X increase in lamp intensity proportionally increases the fiber optic probe sensitivity by 20X. This can easily be accomplished by electronic circuitry that monitors the lamp intensity via a silicon photodiode. The silicon photodiode is linear over several orders of magnitude light intensity so a wide range of sensitivities may be selected entirely by electronic control. Additionally, the lamp monitor photodiode can be used in an electronic servo control to keep the lamp intensity constant, ensuring a stable displacement reading.

Further target movement away from the probe causes a loss of reflected light intensity seen by the receiving fiber (B2) in Figure 4 and produces a decrease in the voltage output. This area of the curve is called the back slope region (Figure 5), typical values as listed as Range 2 in Table 1. Each plug-in module stores the sensitivity factor of the front and back slope providing two distinct operating regions per fiber optic sensor. One highly sensitive area with a small standoff and measurement range and another less sensitive area with a larger standoff and measurement range.

The Fotonic Sensor can also operate at greater standoff distances through the use of MTII’s KD-LS-1A Optical Extender2 (Figure 7). This focuses the light from the fiber optic probe to a point about 0.32 inches (8mm) beyond the front of the most forward lens.

FIGURE 7: KD-LS-1A Fiber Optic Probe Extender

KD-LS-1A  Fiber Optic Probe Extender

When the distance from the front of the KD-LS-1A to the reflecting target is approximately the same as the focal length of the lens assembly, an image of the probe face will appear on the surface of the reflective target. This image is transmitted back through the KD-LS-1A and is reimaged onto the fiber optic probe face. This causes the returning light to enter the transmitting fibers and significantly reduces the light projected onto the receiving fibers. The decrease in light creates a sharp null in the instrument’s output signal as seen in Figure 8.

FIGURE 8: KD-LS-1A Fiber Optic Probe Extender Response Curve Compared to Standard Probe

KD-LS-1A  Fiber Optic Probe Extender Response Curve Compared to Standard Probe

When the target distance is displaced slightly in either direction from the focal point, the image is blurred and the returning light begins to enter the receive fibers again. This action generates a peak in output signal at either side of the null. The displacement/output relationship will be similar to that which would have been obtained with the same probe looking directly at the reflective surface -–except that the standoff distance is now on the order of 100 times greater than before. Other models of the Optical Extender can incorporate a magnification factor to obtain even greater sensitivity while still retaining the advantage of increased operating gap.

Fiber-Optic Probes

The key element of the Fotonic Sensor is the flexible fiber optic probe which consists of two sets of fiber optic filaments jacketed together to form one. Active diameters can be as small as 0.007 inch (0.177mm), making them ideally suited to measure small targets. To provide a wide variety of sensitivities and measurement ranges MTII provides three standard fiber optic probe configurations as shown in Figure 9. These configurations are determined by the distribution of the transmitting and receiving fiber optic filaments in the probe tip.

FIGURE 9: Fiber Optic Probe Configurations

Fiber Optic Probe Configurations

A random fiber distribution is a random mix of the transmitting and receiving fibers. Fiber optic sensors with a random fiber patterns demonstrate high displacement sensitivity because of the close interaction between neighboring fibers, but have a short measurement range.

A hemispherical fiber distribution separates the transmitting and receiving fibers into two distinct groups, with one half of the probe tip composed of transmitting fibers and the other half all receiving fibers. Hemispherical probe tips offer a long range, but low displacement sensitivity.

A concentric transmit inside fiber distribution contains a group of transmitting fibers located at the center of the probe tip surrounded by a concentric group of receiving fibers. This fiber optic probe arrangement offers an intermediate choice between the high-sensitivity/short-range random probe fibers and the long-range/low-sensitivity hemispherical probe fibers. Because of their symmetrical arrangement this style of probe is less affected by tilted targets.

Figure 10 outlines the relative performance of the different fiber optic configurations.

Relative Performance of Different Fiber Optic Sensor Configurations

FIGURE 10: Relative Performance of Different Fiber Optic Sensor Configurations

MTII also offers special fiber optic edge (or shadow) probes. In these arrangements the fiber distribution contains a transmit group of fibers opposing a receive group of fibers. Both transmit and receive bundles can be either random or hemispherical, depending on the application performance required. A thin or narrow target is placed in the gap between the fibers bundles. As a target moves between these bundles a shadow is cast on the receive fibers causing a change in light intensity received. Like standard fiber optic probes this converts to a change in the voltage output of the MTI-2100 Fotonic Sensor, which is related to the edge position. This configuration is particularly effective measuring runout of computer disks, magnetic tapes or displacement of thin ultrasonic horns. Bundle diameters range from 0.02” (.5mm) to 0.09” (2.3mm) with a response typical to that shown in Figure 11.

FIGURE 11: Shows a Typical Response Curve for a Fiber Optic Edge Probe

Shows a Typical Response Curve for a Fiber Optic Edge Probe

In addition to using customized edge probes, standard fiber optic reflectance types can also be used to measure the lateral movement or vibration of a target edge. Since the optical peak is a point of inflection on the performance curve it is an area where the received light of the fiber optic sensor does not change with small target displacements. Taking advantage of this characteristic allows the sensor to be used to measure changes in reflectivity or position of an edge, independent of motion in the normal direction. By traversing a target across the probe face a unique output curve is generated and can be used to precisely determine position. Figure 12 shows two examples of the output from a fiber optic sensor verses lateral edge position. Note that different sensitivities can be obtained by orientating the probe 90 degrees. Different fiber distributions also produce different sensitivities, allowing sensors to fulfill a variety of application requirements.

FIGURE 12: Fiber Optic Sensor Response Curve to Lateral Target Motions

Fiber Optic Sensor Response Curve to Lateral Target Motions Fiber Optic Sensor Response Curve to Lateral Target Motions

Reflectance compensated fiber optic probes consist of three sets of fibers as shown in Figure 13. The first set consists of a random bundle located in the center. Flanking this bundle are two sets of receive fibers, each with different numerical apertures. The two separate receive bundles permit compensation for different surface reflectivities, eliminating the need for calibration as is done with standard fiber optic probes. Because of their reflectance compensation ability they are particularly effective measuring displacements of targets that have lateral movement. Reflectance compensated probes also work through optical extenders, offering similar increases in the probe operating standoff, with the added benefit of reflectivity compensation.

FIGURE 13: Typical Response Curve for a Reflectance Compensated Fiber Optic Sensor

Typical Response Curve for a Reflectance Compensated Fiber Optic Sensor

The selection of a particular probe configuration depends on the application requirements. Table 1 outlines the performance of different probe diameters and fiber arrangements. From the table you will see that the sensitivity for “random” style probes is approximately 5-10 times better than “hemispherical” probes. A similar decrease in linear range also exists. It is also important to note that the signal to noise ratio increases with larger diameter fiber bundles. This is because of the increased number of fibers within the probe, resulting in improved light collection.

TABLE 1: Fiber Optic Probe Module Specifications

Fiber Optic Probe Module Specifications

Custom probe configurations are available for specialized applications. Please contact MTII’s Application Engineers for assistance.

Surface Reflectivity And Pressure

The Fotonic Sensor can be used to monitor changes in surface reflectivity and/or changes in light transmission through a media. This is useful for surface finish comparison and surface flaw-detection applications. Additionally, fiber optic sensors may be employed in pressure monitoring application where varying pressure changes the position or reflectance of a target. The non-contact, no-hysteresis characteristics of fiber optic sensors make them particularly suitable for transducers and high frequency applications. Fiber-optic sensors may also be operated in nearly any gaseous or liquid media. Vacuum or pressure bushings can be built along the fiber optic probe buncle, or even on the probe tip itself allowing the Fotonic Sensor to be used in pressure/vacuum applications.




 Summary:

MTI Instruments Inc.
325 Washington Avenue Extension
Albany, NY 12205-5505 USA
Phone: 518-218-2550
Toll Free (US): 800-342-2203
Fax: 518-218-2506
E-mail:

Fotonic Vibration Monitoring/Gaging Systems, Fiber optic Displacement Probes, Optical Position Sensors, Fiberoptic Displacement Gap Measurement Gauging, Non-contact Dimensional Metrology, Distance Sensor Gage, Precision Edge Runout Measuring Guage, MTI-1000